Adjustment of the Main Drive Gap of Wheeled Construction Machinery Drive Axle
1. Check and adjust the bearing clearance of the driving bevel gear. The bearing clearance of the driving bevel gear is generally 0.05-010mm. When the clearance exceeds 0.10mm, it should be adjusted: fix the dial indicator on the axle housing, and the contact of the meter is against the driving gear The outer end of the gear shaft, and then axially pry the upper flange of the gear shaft, the absolute value of the maximum and minimum readings of the dial gauge is the bearing clearance; when adjusting, you can increase or decrease the adjustment gasket between the inner ring of the driving gear bearing and the shaft shoulder. If you add a gasket, the bearing becomes loose, and vice versa.
2. Inspection and adjustment of the bearing clearance of the driven bevel gear. The normal clearance of the left and right bearings of the driven bevel gear is 0.05-0.10mm, which can be adjusted by the adjustment rings on both sides of the differential housing. First, remove the lock plate on the adjustment ring, and then twist the two adjustment rings to adjust (the two adjustment rings must be screwed in or out at the same time to ensure the meshing gap and impression of the gear pair); after adjustment, the driven gear should be It is suitable to rotate flexible and have a little resistance, but there is no loose feeling.
3. The adjustment of the thrust screw of the driven Wheel Loader Bevel Gear. For construction machinery with thrust screws on the back of the driven gear (such as ZL50 loader), the gap between the end of the thrust screw and the back of the driven gear should be 0.20-0.40mm . When adjusting, first loosen the fixing nut, then tighten the screw and back 1/3 turn, and then lock the fixing nut.
4. Inspection and adjustment of the meshing clearance and impression of the driving and driven bevel gears. Inspection methods and standards: When checking the meshing of the driving and driven bevel gears, the tooth surface of the driving bevel gear is usually coated with red lead oil first. In the case of gear meshing, turn the gear with a little resistance, and then check the traces on the Teeth of the driven gear; when meshing correctly, the contact length of the imprint should be about 2/3 of the full tooth length, and the contact traces are 2-4cm from the small end .(Main Drive,Axle Of Sdlg Loader,Pinion Ring Gear,Wheel Loader Bevel Gear)
Main Drive Main Drive,Axle Of Sdlg Loader,Pinion Ring Gear,Wheel Loader Bevel Gear Shandong Tianfu International Trade Co.,Ltd. , https://www.tfloaderparts.com
Process to peel the quail eggs:Â
Cooking eggs------Cooling eggs -----Breaking the shell of eggs (to soften the shell for better peeling) ------Peeling
Characteristics:
1. Special machine for shelling quail egg, high efficiency, low breakage rate.
2. Made of stainless steel, safety and hygiene.
3. Special design, compact structure, beauty and utility.
4. It's suitable for manufacturers of spiced quail egg and quail egg can products.
Operating principle of quail egg shell peeler:
Motor rotation drive gear, by mechanical drive the sponge mat move up and down and rubber tube counter rotating create friction, thus the quail egg shells torn from the surface, to achieve the effect of shelling.
Application:
can be used for snack foods such as spiced corned egg, white egg processing industry.
Specification of Quail eggs shelling machine:
Â
Type
Quail egg shell peeling machine
Model
NW-206
Capacity
200kg/h
Power
180W
Voltage
220V 50HZ
Overall dimension
1.1*0.7*0.9m
Weight
100kg
We also provide Chicken/Duck Egg grading machine,chicken egg shell peeling machine,egg incubators
Newin Company contact information:
Contact person:Cindy
Mobile 86-15838059235
220V/110V Professional Stainless Steel Quail Egg Peeling Machine
Model NO.: NW-206
Power: 180W
Voltage: 220V
Machine Weight: 100kg
Trademark: Newin
Transport Package: Non-Fumigation Wooden Case
Specification: 1.1*0.7*0.9m
Origin: China
HS Code: 8438600000
Quail egg Peeling machine/Quail egg Peeler machine